SMP800C compliant sheet for mass transit applications
Introduction
KYDEX® 2200LT is a high performance thermoplastic sheet designed for use in mass transit interior applications where SMP800C or BSS7239 compliance is required.
General
Information
KYDEX® 2200LT is a cost effective alternative to FRP that offers the additional benefit of weight savings. It meets INFORMATION the Federal Transit Administration (FTA) and the Federal Rail Administration (FRA) requirements for smoke emission and flammability as tested under ASTM E-662 and ASTM E-162. Additionally, KYDEX® 2200LT meets the toxicity criteria defined by SMP800C and BSS7239.
Suggested
Applications
- Seatbacks • Bulkhead Components
- APPLICATIONS • Armrests • Wall and Ceiling Panels
- Window Shrouds
Features
- Meets flamespread and smoke development requirements listed in 49 CFR 238
- Compliant to SMP800C and BSS7239 toxicity specifications
- Excellent formability and fabrication characteristics
- Allows for tight tolerance control
- Excellent resistance to graffiti, chemicals, and staining
Environmental
& Safety
Considerations
SEKISUI KYDEX is committed to ensuring that its products can be manufactured, transported, stored, used, & SAFETY disposed and recycled with an appropriate regard for safety, health, and environmental protection. We support the safe handling of our products.
Please contact our appLab™ department at 800.682.8758 for resources and Safety Data Sheets or visit our website: www.kydex.com.
| Property | Test Method | Typical Value1 | |
|---|---|---|---|
| PHYSICAL | |||
| Specific Gravity | ASTM D792 | 1.30 | |
| Density | ASTM D792 | 1.30 g/cm3 | 0.047 lb/in3 |
| Water Absorption, 24 hr. | ASTM D570 | 0.17% | |
| Rockwell Hardness, R-scale | ASTM D785 | 108 | |
| MECHANICAL | |||
| Tensile Strength | ASTM D-638 | 52.7 MPa | 7,650 psi |
| Tensile Modulus | ASTM D-638 | 3,895 MPa | 565,000 psi |
| Flexural Strength | ASTM D-790 | 77.9 MPa | 11,300 psi |
| Flexural Modulus | ASTM D-790 | 3,110 MPa | 451,000 psi |
| Compressive Strength, yield | ASTM D-695 | 71.7 MPa | 10,400 psi |
| Compressive Modulus | ASTM D-695 | 3,964 MPa | 575,000 psi |
| Shear Strength | ASTM D-732 | 42 MPa | 6,090 psi |
| Bearing Strength, 4% deflection | ASTM D-953 | 41 MPa | 5,940 psi |
| Bearing Strength, max. | ASTM D-953 | 232.4 MPa | 33,700 psi |
| Notched Izod Impact | ASTM D-256 | 140 J/m | 2.61 ft-lb/in f |
| Garnder Drop Dart Impact, GE | ASTM D-5420 | 40.9 J | 362 in-lb f |
| Garnder Drop Dart Impact, GE @ -20°F (-29°C) | ASTM D-5420 | 14.2 J | 126 in-lb f |
| THERMAL | |||
| Heat Deflection Temperature (HDT) @ 264 psi (1.8 MPa) Annealed | ASTM D648 | 89.0°C | 192.2°F |
| Coefficient of Thermal Expansion | ASTM E831 | 53.8 µm/m/°C | 29.9 µin/in/°F |
| ELECTRICAL | |||
| Dielectric Strength, oil | ASTM D149 | 23.9 kV/mm | 588 V/mil |
| FLAMMABILITY2 | |||
| Flammability: Flame Spread Index | ASTM E-162 | I <35 S No Burning Drip | |
| Flammability: Smoke Density | ASTM E-662 | D(1.5) <100 S D(4.0) <200 S | |
| Bombardier Toxic Gas Generation | SMP 800-C | Pass | |
| Boeing Toxic Gas Generation | BSS 7239 | Pass | |
| Caloric Content | ASTM E-1354 | 5,084 BTU/lb | |
| 1 Values based upon 3.18mm (0.125”) sheet unless otherwise specified. 2 All thicknesses and colours Not intended for specification purposes. | |||