High Impact TPO, Low Gloss Sheet
Introduction
ALLEN® T3050LG is a general purpose TPO that has high impact properties and a good cost to performance ratio to other materials like steel, FRP, aluminum, and other thermoplastics.
General
Information
ALLEN® T3050LG has been tested under laboratory conditions and has achieved a UL94 HB rating at 0.060 in INFORMATION (1.52mm) and above and meets the requirements of Federal Motor Vehicle Safety Standard No. 302 (FMVSS 302).
Suggested
Applications
- Vehicle Interiors
- APPLICATIONS • Industrial Housings
- Heavy Equipment parts
- Agriculture Equipment parts
- Antenna covers
- Exterior RV components
Features
- UV and non UV resistant products available
- Excellent low temperature impact strength
- Edge trim easily used into future orders
- Excellent chemical resistance
- High heat resistance
- Low gloss finish only
Environmental
& Safety
Considerations
SEKISUI KYDEX, LLC is committed to ensuring that its products can be manufactured, transported, stored, used, & SAFETY disposed and recycled with an appropriate regard for safety, health, and environmental protection. We support the safe handling of our products.
Please contact our appLab™ department at 800.682.8758 for resources and Safety Data Sheets or visit our website: www.kydex.com.
| Property | Test Method | Typical Value1 | |
|---|---|---|---|
| PHYSICAL | |||
| Specific Gravity | ASTM D792 | 1.13 g/cc | |
| Water Absorption, 24hr | ASTM D570 | 0.01% | |
| Rockwell Hardness, R-Scale | ASTM D785 | 51 | |
| MECHANICAL | |||
| Tensile Strength | ASTM D638 | 19.8 MPa | 2,870 psi |
| Tensile Modulus | ASTM D638 | 2,709.6 MPa | 393,000 psi |
| Flexural Stress at 5% Strain | ASTM D790 | 29.2 MPa | 4,230 psi |
| Flexural Modulus | ASTM D790 | 2,282.2 MPa | 331,000 psi |
| Compressive Strength, yield | ASTM D695 | 23.1 MPa | 3,350 psi |
| Shear Strength | ASTM D732 | 20.1 MPa | 2,910 psi |
| Bearing Strength, 4% deflection | ASTM D953 | 18.1 MPa | 2,630 psi |
| Bearing Strength, max. | ASTM D953 | 96.5 MPa | 14,000 psi |
| Notched Izod Impact Resistance | ASTM D256 | 683.5 J/m | 12.8 ft-lbs/in |
| Gardner Drop Dart Impact, GE | ASTM D5420 | 34.1 J | 302 in-lb |
| THERMAL | |||
| Heat Deflection Temperature (HDT) 264 psi (1.8 MPa), Unannealed | ASTM D648 | 59.9°C | 139.7°F |
| Heat Deflection Temperature (HDT) 66 psi (0.45 MPa), Unannealed | ASTM D648 | 116°C | 240.6°F |
| Coefficient of Thermal Expansion (MD) | ASTM E831 | 39.5 μm/m/°C | 22 μin/in/°F |
| ELECTRICAL | |||
| Dielectric Strength, oil | ASTM D149 | 22.9 kV/mm | 580 V/mil |
| FLAMMABILITY | |||
| Underwriters Laboratories, Inc.® Component Recognition | UL Standard 942 | HB @ 0.060 in (1.52mm) | |
| Motor Vehicle Safety Standard | FMVSS 302 | Pass | |
| 1 Values based upon 0.125” (3.17mm) sheet unless otherwise specified. 2 ALLEN® T3050LG has been tested under laboratory conditions and has passed UL 94HB criteria. SEKISUI KYDEX, LLC makes no warranty or guarantee that these products will meet UL 94HB in the part’s final, finished configuration. Not intended for specification purposes. | |||