Co-extruded, High Impact ABS, Soft Touch Sheet
Introduction
ALLEN® 5300WST is a co-extruded sheet consisting of a soft-touch, low gloss ASA cap over a high impact ABS substrate. It is designed to provide a sheet with high impact resistance with a tactile, non-slip surface.
General
Information
ALLEN® 5300WST meets the requirements of Federal Motor Vehicle Safety Standard No. 302 (FMVSS 302) at 0.060” (1.52mm).
Suggested
Applications
- Truck interiors
- Recreational vehicles
- Agricultural cab interiors
- Dashes/Consoles
- Shrouds
Features
- Custom color matching
- Ease of processing
- Regrind compatible in future orders
- Matte gloss finish
- High impact resistance
- Slip resistance
Environmental
& Safety
Considerations
SEKISUI KYDEX®, LLC is committed to ensuring that its products can be manufactured, transported, stored, used, disposed and recycled with an appropriate regard for safety, health and environmental protection. We support the safe handling of our products. Please contact our Technical Service department at 800.682.8758 for resources or visit our website: http://www.kydex.com. For Material Safety Data Sheets, please call 800.325.3133.
| Property | Test Method | Typical Value1 | |
|---|---|---|---|
| PHYSICAL | |||
| Specific Gravity (Density) | ASTM D792 | 1.05 (1.05 g/cm3) | |
| Moisture Absorption, 24 hr | ASTM D570 | 0.50% | |
| Rockwell Hardness, R-Scale | ASTM D785 | 70 | |
| Gloss (60o) | ASTM D2457 | 102 | |
| MECHANICAL | |||
| Tensile Strength, yield | ASTM D638 | 36.9 MPa | 5,350 psi |
| Tensile Modulus | ASTM D638 | 1,875.4 MPa | 272,000 psi |
| Flexural Stress at 5% Strain | ASTM D790 | 49.6 MPa | 7,200 psi |
| Flexural Modulus | ASTM D790 | 1,578.9 MPa | 229,000 psi |
| Compressive Strength, yield | ASTM D695 | 50.6 MPa | 5,110 psi |
| Shear Strength | ASTM D732 | 37.4 MPa | 4,970 psi |
| Bearing Strength, 4% deflection | ASTM D953 | 20.3 MPa | 1,760 psi |
| Bearing Strength, max. | ASTM D953 | 171.7 MPa | 17,200 psi |
| Notched Izod Impact Resistance | ASTM D256 | 320 J/m | 6.0 ft-lbs/in |
| Gardner Drop Dart Impact | ASTM D5420 | 35.6 J/m | 316 in-lbsf |
| THERMAL | |||
| Heat Deflection Temperature (HDT) 264 psi (1.8 MPa), Unannealed | ASTM D648 | 80.5°C | 177°F |
| Heat Deflection Temperature (HDT) 66 psi (0.45 MPa), Unannealed | ASTM D648 | 94.0°C | 201°F |
| Coefficient of Thermal Expansion (MD) | ASTM E831 | 89.9 μm/m/°C | 49.9 μin/in/°F |
| ELECTRICAL | |||
| Dielectric Strength, oil | ASTM D149 | 18.7 kV/mm | 475 V/mil |
| FLAMMABILITY | |||
| Motor Vehicle Safety Standard3 | FMVSS 302 | Pass | |
| 1 Values based upon 0.125” (3.17mm) sheet unless otherwise specified.. 2 Value will vary depending on sheet texture. Stated value will represent upper limit on a smooth surface. 3 0.060” (1.52mm) and above Not intended for specification purposes. | |||